[yurii-62]

Обновления для RIFF Box: от 25.10.2013

ZTE Racer x850
Samsung Galaxy S II LTE SC-03D (Samsung CeloX-)
Samsung GT-i9295 Galaxy S4 Active (Samsung Fortius)
Samsung GT-i9190 Galaxy S4 Mini (Samsung Serrano)
HTC Panache 4G
HTC One M7 PN072000
HTC One M7 PN071100
HTC Butterfly DLX
Fly IQ 280

Источник.. http://www.riffbox.org/category/jtag-news/

News

25.10.2013 RIFF JTAG – Easy repair Samsung A777 supported

The Samsung A777 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung A777:
Solder JTAG cable to Samsung A777 JTAG pads;
connect USB cable;
Make sure Samsung A777 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘9’ key and press ‘Power ON’ button.

25.10.2013 RIFF JTAG – Easy repair Fly IQ 280 supported

Repairing bricked Fly IQ280 is easy with the RIFF Box.

To resurrect Fly IQ280:
Solder JTAG cable to Fly IQ280 JTAG pads;
Insert Fly IQ280 into any USB port for power and attach battery if required;
Make sure Fly IQ280 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

25.10.2013 RIFF JTAG – Easy repair HTC Butterfly X920d (HTC DLX) supported

Repairing bricked HTC Butterfly (PL9911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.41.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PL9911000’.

To resurrect HTC Butterfly:
Solder JTAG cable to HTC Butterfly (PL9911000) JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Butterfly (PL9911000) is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

25.10.2103 RIFF JTAG – Easy repair HTC One M7 PN071100 supported

Repairing bricked HTC OneM7 U (PN0711000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.44.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PN0711000’.

To resurrect HTC OneS:
Solder JTAG cable to HTC OneM7 U (PN0711000) JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC OneM7 U (PN0711000) is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

25.10.2013 RIFF JTAG – Easy repair HTC Panache 4G supported

Repairing bricked HTC Panache is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zones and will re-write PDA’s SPL to 0.89.0005 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Panache via USB Cable:
If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
Make sure USB cable is attached to the board and is connected to PC;
Make sure HTC Panache via USB is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

25.10.2013 RIFF JTAG – Easy repair Samsung GT-i9190 Galaxy S4 Mini (Samsung Serrano) supported

Repairing bricked Samsung I9190 is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0*****215;42 error during connection stage.

To resurrect Samsung I9190:
Solder JTAG cable to Samsung I9190 JTAG pads;
Connect USB cable or insert battery;
Make sure Samsung I9190 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

25.10.2013 RIFF JTAG – Easy repair Samsung GT-i9295 Galaxy S4 Active (Samsung Fortius) supported

Repairing bricked Samsung I9195 is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0*****215;42 error during connection stage.

To resurrect Samsung I9195:
Solder JTAG cable to Samsung I9195 JTAG pads;
Connect USB cable or insert battery;
Make sure Samsung I9195 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

25.10.2013 RIFF JTAG – Easy repair Samsung Galaxy S II LTE SC-03D (Samsung Celox) supported

Repairing bricked Samsung SC-03D is easy with the RIFF Box. The device is based on the 2nd-generation Qualcomm MSM8260 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung SC-03D:
Solder JTAG cable to Samsung SC-03D JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung SC-03D is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press Power-On.

25.10.2013 RIFF JTAG – Easy repair ZTE Racer X850 supported

Repairing bricked ZTE Racer is easy with the RIFF Box.

To resurrect ZTE Racer:
Solder JTAG cable to ZTE Racer JTAG pads;
Connect ZTE Racer tablet’s charger for power;
Make sure ZTE Racer is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.