Успешное применение, без комментариев [InfinityBox CM2 SPD] - GSM Форум

**gulka** · 02.11.2015, 12:38

BQS-3510 SC77xx_NAND снес код

Operation : Format File System [ v1.05 ]

**gulka** · 23.11.2015, 13:41

Supra M74DG Sc7731

Operation : Read FullFlash [ v1.06 ]

**gulka** · 24.11.2015, 18:33

Планшет TEXET X-pad HIT 7 3G TM-7866 SC5735

Operation : Read FullFlash [ v1.06 ]

**gulka** · 02.12.2016, 14:08

Встретил FLY FS454 Nimbus 8 на SPD, везде он MTK

Прочесть граф.ключ не смог , снес форматом
Operation : Read PatternLock [ v1.24 ]

Код:

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 24 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : Infinity SC773x eMMC v3 LDR      
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

FlashMode Set : Ok!
Reading PatternLock ... 
PatternLock Not Set!

Elapsed: 00:00:19

Reconnect Power/Cable!

Operation : Check/Read Info [ v1.24 ]

Код:

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 24 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : Infinity SC773x eMMC v3 LDR      
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ... 

Model Name  : FS454
Model Brand : Fly
Model Device: Nimbus_8
AndrVersion : 6.0
BaseBand CPU: SP7731CEB
CompileDate : 26.09.2016 6:35:43
Project Ver : SW05_FLY_FS454_2016_09_26
Model Ext   : FS454

ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Elapsed: 00:00:22

Reconnect Power/Cable!

FLY FS454 Nimbus 8 Прошивка для SPD

Operation : Read FullFlash [ v1.24 ]

Код:

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 24 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : Infinity SC773x eMMC v3 LDR      
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ... 

Phone found! [ 24 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : Infinity SC773x eMMC v3 LDR      
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ... 

Phone found! [ 24 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : Infinity SC773x eMMC v3 LDR      
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : FS454
Model Brand : Fly
Model Device: Nimbus_8
AndrVersion : 6.0
BaseBand CPU: SP7731CEB
Project Ver : SW05_FLY_FS454_2016_09_26
Model Ext   : FS454

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ... 

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : udc_config.bin
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1886 MiB
Saved to : C:\Users\TIMUR\Desktop\SP7731CEB_Nimbus_8_6.0_SW05_FLY_FS454_2016_09_26_FS454\
Done!

Elapsed: 00:13:25

Reconnect Power/Cable!

cloud · 20.01.2017, 23:33

Цитата:

Сообщение от gulka

Встретил FLY FS454 Nimbus 8 на SPD, везде он MTK

Прочесть граф.ключ не смог , снес форматом

Аналогичная история, только SW04, ключ тоже не смог, и читается что интересно при выборе SP [SC7730/SC7731] EMMC Crev / Android 6.x как без галки Alternative LDR Mode так и с ней, а в примере выше вообще Boot Ver : Infinity SC773x eMMC v3 LDR, наверное поэтому что при чтении пишет ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Чтение инфо без галки Alt Ldr

Чтение инфо с галкой Alt Ldr

Чтение прошивки без галки Alt Ldr

motokmips · 13.01.2017, 17:29

Irbis TX35

Цитата:

Operation : Check/Read Info [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 35 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name : scx35_sp7731gea_k03_nm_nc74_64_8plus_dt
Model Brand : IRBIS
Model Device: scx35_sp7731gea_k03_nm_nc74_64_8
AndrVersion : 4.4.2
BaseBand CPU: SP7731GEA_K03_NM_NC74_64_8
CompileDate : 28.10.2015 11:03:26
Project Ver : KOT49H 14B_test-keys
Model Ext : TX35

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:21

Reconnect Power/Cable!

Operation : Read NV [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 35 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Detected eMMC Flash , Structure detect Ok!

Read GSM NV
Read WCN NV

Read Ok , 0x00029670
Saved to : C:\InfinityBox\CM2SPD\phdata\backup\Irbis_TX35_CX_ SPDNV.spdnv

Elapsed: 00:00:53

Reconnect Power/Cable!

uploads · 13.01.2017, 22:19

Prestigio PSP3503

Цитата:

Model Name : PSP3503DUO
Model Brand : Prestigio
Model Device: PSP3503DUO
AndrVersion : 4.4.2
BaseBand CPU: SC7731
Project Ver : PSP3503DUO.20150709.1.0.11
Model Ext : PSP3503DUO

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ...

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : nvitem_w.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.22.3_Release.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1570 MiB
Saved to : C:\Users\User\Desktop\PSP3503\SC7731_PSP3503DUO_4. 4.2_PSP3503DUO.20150709.1.0.11_PSP3503DUO\
Done!

Elapsed: 00:06:11

Reconnect Power/Cable!

Nickeron · 17.01.2017, 10:44

Сброс графического ключа

Код:

Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 69 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000000801F7000
State : 0x0001

Mount : /cache
Size  : 0x0000000013600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:22

Чтение FullFlash

Код:

Operation : Read FullFlash [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 69 ]
Port Opened
Sync...
Initial Boot Failed!

Reconnect Power/Cable!


Operation : Read FullFlash [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 69 ]
Port Opened
Sync...
Initial Boot Failed!

Reconnect Power/Cable!


Operation : Read FullFlash [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 69 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ... 

Phone found! [ 69 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ... 

Phone found! [ 69 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : PSP3403DUO
Model Brand : Prestigio
Model Device: GF40B1G
AndrVersion : 5.1
BaseBand CPU: SC7731G
Project Ver : PSP3403DUO.20160903.1.0.12
Model Ext   : PSP3403DUO

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ... 

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.43.3_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : oem.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1380 MiB
Saved to : E:\SC7731G_GF40B1G_5.1_PSP3403DUO.20160903.1.0.12_PSP3403DUO\
Done!

Elapsed: 00:09:40

**jblack** · 17.01.2017, 15:26

Парни прячьте логи под теги [SPOILER] или хотя бы [CODE], а то не удобно просматривать темы, кому нужно тот раскроет и посмотрит.

Nickeron · 20.01.2017, 11:16

Operation : Check/Read Info [ v1.24 ]

Operation : Read FullFlash [ v1.24 ]

Operation : Flash [ v1.24 ]

**JayDi** · 21.01.2017, 17:26

Не читается граф ключ на 6 и выше, там "GateKeeper" стоит.

metam · 22.01.2017, 17:23

Удаление FRP на Micromax Q465

Код:

Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 115 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC9830 eMMC Generic Loader v2 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000002DC8F7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:20

Reconnect Power/Cable!

Девайс на SC9832 которого нет в списке! Выбрал SC9830 и frp снят)
Зачет Jaydi

**renat_d** · 01.02.2017, 22:15

Успешно снял FRP на Fly FS406 (SC7731C)

Operation : Format File System / Reset Settings [ v1.24 ]

PS Долго не мог подключить этот хитрый Fly к компу.

Оказалось, чтобы подключить его, нужно сначала вставить USB кабель, а потом зажать клавишу "Громкость -". JayDi респект

**JayDi** · 01.02.2017, 23:48

Можно иначе - кабель, кнопки, батарейку после.

Bexruz.19 · 02.02.2017, 07:02

ZTE Blade AF5 Read Pattern

Код:

Operation : Read PatternLock [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 77 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

FlashMode Set : Ok!
Reading PatternLock ... 
Read Ok , decrypt
PatternLock Sequence : 32589

Done!

Elapsed: 00:00:29

Reconnect Power/Cable!

Bexruz.19 · 02.02.2017, 07:05

TEXET TM7866 Read Flash

Код:

Operation : Read FullFlash [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 77 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC5735 eMMC Loader v1.01 Inf     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ... 

Phone found! [ 77 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC5735 eMMC Loader v1.01 Inf     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ... 

Phone found! [ 77 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC5735 eMMC Loader v1.01 Inf     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : scx35_sp5735c2eaplus_s906_rgb_UUI
Model Brand : teXet
Model Device: tm7866rev1
AndrVersion : 4.4.2
BaseBand CPU: SP5735C2EA
Project Ver : V1.1.KITKAT.rus.teXet.20150619.094104
Model Ext   : X-pad HIT 3G (revision 1)

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ... 

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc8830_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830_modem_CP2_WCN_14C_W14.51_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_1024x600.bin
[Read Ok] : fblogo_768x1024.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 863 MiB
Saved to : C:\WORKSPACE\SP5735C2EA_tm7866rev1_4.4.2_V1.1.KITKAT.rus.teXet.20150619.094104_X-pad_HIT_3G_(revision_1)\
Done!

Elapsed: 00:03:31

Reconnect Power/Cable!

cloud · 10.02.2017, 22:20

Fly Stratus 6 FS407

Check/Read Info [ v1.24 ]

Read NV [ v1.24 ]

Read FullFlash [ v1.24 ]

SurTaX · 17.02.2017, 09:48

Lenovo A396 SC8830 NAND Reset User Code

лог

**gulka** · 03.03.2017, 16:21

BQ-4026 UP! Прошивка

Operation : Read FullFlash [ v1.24 ]

Код:

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 40 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ... 

Phone found! [ 40 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ... 

Phone found! [ 40 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : BQ-4026
Model Brand : BQ
Model Device: BQ-4026
AndrVersion : 6.0
BaseBand CPU: BQ-4026
Project Ver : MRA58K release-keys
Model Ext   : BQ-4026

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ... 

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1331 MiB
Saved to : C:\Users\TIMUR\Desktop\BQ-4026_BQ-4026_6.0_MRA58K_release-keys_BQ-4026\
Done!

Elapsed: 00:09:33

Reconnect Power/Cable!

motokmips · 22.03.2017, 11:13

FLY IQ4490i Прошивка

Код:

Start  at : [22.03.2017 / 9:48:55]
Operation : Flash [ v1.24 ]

======= Flash
Files set for flashing : 
[ MCU ] : IQ4490i_SW_20151008_SW14_FLY.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SC7715
PacVersion : SW14_FLY_IQ4490i_20151008
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : SC7702_sc7715_modem.bin
File : DSP_DM_G2.bin
File : SC8800G_sc7715_wcn_modem.bin
File : LOGO.bmp
File : LOGO.bmp(1)
File : boot.img
File : system.img
File : cache.img
File : recovery.img
File : userdata.img
File : u-boot.bin

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 35 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x17 records
PMTManager : PMT Update Ok!
Flashing now

[FlashProc] : CODE  
Current ID : PRODNV
Current File : prodnv.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_W
Current File : SC7702_sc7715_modem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_W
Current File : DSP_DM_G2.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WCN
Current File : SC8800G_sc7715_wcn_modem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOTLOGO
Current File : LOGO.bmp
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : FASTBOOT_LOGO
Current File : LOGO.bmp(1)
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOT
Current File : boot.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : RECOVERY
Current File : recovery.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEMISC
Current Part : misc
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : UBOOTLOADER
Current File : u-boot.bin
Flashing now ... 
[FlashProc] : Ok!


Elapsed: 00:03:28

Reconnect Power/Cable!

Finish at : [22.03.2017 / 9:52:50]

02.11.2015, 12:38	#1
gulka Супермодератор Регистрация: 10.11.2005 Адрес: Russia Сообщений: 2,979 Поблагодарил: 805 Поблагодарили 6,951 раз за 1,594 сообщений Репа: 1190	Успешное применение, без комментариев [InfinityBox CM2 SPD] BQS-3510 SC77xx_NAND снес код Operation : Format File System [ v1.05 ] Loading : W_WCN_NAND.pac CRVersion : BP_R1.0.0 PacCPUinfo : SC77xx_NAND PacVersion : MocorDroid4.4_3.10_7715_P14.30.2_P7 FastCheck : 0x1F143CF2 Loading files ... File : fdl1.bin File : fdl2.bin File : wnvitem.bin File : wcnnvitem.bin File : prodnv_b256k_p4k.img File : u-boot-spl-16k.bin File : wmodem.bin File : wdsp.bin File : wcnmodem.bin File : ubootlogo.bmp File : boot.img File : system_b256k_p4k.img File : cache_b256k_p4k.img File : recovery.img File : userdata_b256k_p4k.img File : u-boot.bin File : prodnv_b128k_p2k.img File : system_b128k_p2k.img File : cache_b128k_p2k.img File : userdata_b128k_p2k.img File : SC7715_nand.xml Load Ok! Start at : [02.11.2015 / 12:24:43] Operation : Format File System [ v1.05 ] Settings : SmartFormat is On 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 6 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable PickUp loaders from pac FDL Ready! Boot Ver : Spreadtrum Boot Block version 1.1 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Checking Structure ... Detected NAND Flash , Structure detect Ok! Formatting NAND Flash Format UserData Format Ok! Format Cache Format Ok! Done! Elapsed: 00:00:27 Reconnect Power/Cable! Finish at : [02.11.2015 / 12:25:10] __________________ Скучно.....хочется компанию....Маленькую нефтянную компанию paypal.me/STimur

17.01.2017, 15:26	#9
jblack Администратор Регистрация: 02.08.2004 Адрес: Тридевятое царство Сообщений: 2,210 Поблагодарил: 1,130 Поблагодарили 2,421 раз за 1,091 сообщений Репа: 1993	Парни прячьте логи под теги [SPOILER] или хотя бы [CODE], а то не удобно просматривать темы, кому нужно тот раскроет и посмотрит. __________________ В правильно поставленном вопросе содержится большая часть ответа.

20.01.2017, 11:16	#10
Nickeron Новичок Регистрация: 16.01.2006 Адрес: Украина Сообщений: 18 Поблагодарил: 1 Поблагодарили 12 раз за 5 сообщений Репа: 0	S-TELL C555 scx35_s7358_qhd Operation : Check/Read Info [ v1.24 ] 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 24 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FLASH : eMMC Flash , Structure : Ok! Reading extended info ... Model Name : s7358_qhd_plus_dt_Multi Model Brand : S-TELL Model Device: scx35_s7358_qhd AndrVersion : 5.1 BaseBand CPU: S7358_QHD CompileDate : 18.11.2015 15:20:26 Project Ver : S7358_HWD_X156_S-TELL_QHD_L_B1V01.01B02 Model Ext : C555 ExtraInfo : HWInfo not exists, normal phone Elapsed: 00:00:18 Operation : Read FullFlash [ v1.24 ] 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 24 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Detected eMMC Flash , Structure detect Ok! [FW_READER] : Prepare Ok! - > Wait phone connected ... Phone found! [ 24 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! - > Wait phone connected ... Phone found! [ 24 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! Model Name : s7358_qhd_plus_dt_Multi Model Brand : S-TELL Model Device: scx35_s7358_qhd AndrVersion : 5.1 BaseBand CPU: S7358_QHD Project Ver : S7358_HWD_X156_S-TELL_QHD_L_B1V01.01B02 Model Ext : C555 [Read Mode] : HSUSB : 0x3000 [FW_READER] : Reading Firmware Now ... [Read Ok] : u-boot-spl-16k.bin [Read Ok] : u-boot.bin [Read Ok] : prodnv.img [Read Ok] : sc7731g_CP0_modem.bin [Read Ok] : DSP_DM_Gx.bin [Read Ok] : nvitem_w.bin [Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin [Read Ok] : nvitem_wcn.bin [Read Ok] : logo_540x960.bin [Read Ok] : boot.img [Read Ok] : system.img [Build Ok] : cache.img [Read Ok] : recovery.img [Build Ok] : userdata.img AndroidInfo created Firmware Size : 1019 MiB Saved to : E:\S7358_QHD_scx35_s7358_qhd_5.1_S7358_HWD_X156_S-TELL_QHD_L_B1V01.01B02_C555\ Done! Elapsed: 00:07:38 Reconnect Power/Cable! Operation : Flash [ v1.24 ] ======= Flash Files set for flashing : [ MCU ] : SC77xx Infinity Package 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 24 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SPRD 773x eMMC loader v3 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! [FL] : Enabled NVM update. Will program all NVM images found in FW ! PMTManager : Load 0x18 records PMTManager : PMT Update Ok! Flashing now Update BootCode : u-boot-spl-16k.bin Write Data ... Write Data Ok! Update BootCode : u-boot.bin Erase block ... Block erase Ok! Write Data ... Write Data Ok! Write FSImage : prodnv.img Write Data ... Write Data Ok! Write CodeData : sc7731g_CP0_modem.bin Write Data ... Write Data Ok! Write CodeData : DSP_DM_Gx.bin Write Data ... Write Data Ok! Update NVM image : nvitem_w.bin Update NVM Data Ok! Erase Block : RuntimeData Erase block ... Block erase Ok! Write CodeData : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin Write Data ... Write Data Ok! Update NVM image : nvitem_wcn.bin Update NVM Data Ok! Erase Block : RuntimeData Erase block ... Block erase Ok! Write CodeData : logo_540x960.bin Write Data ... Write Data Ok! Write CodeData : boot.img Write Data ... Write Data Ok! Write FSImage : system.img Write Data ... Write Data Ok! Write FSImage : cache.img Write Data ... Write Data Ok! Write CodeData : recovery.img Write Data ... Write Data Ok! Erase Block : MISC Erase block ... Block erase Ok! Write FSImage : userdata.img Write Data ... Write Data Ok! Erase Block : INTERNALSD Erase block ... Block erase Ok! Elapsed: 00:02:07 Reconnect Power/Cable!

01.02.2017, 22:15	#13
renat_d Почетный пользователь Регистрация: 03.03.2005 Адрес: Поволжье Ершов Сообщений: 1,092 Поблагодарил: 4,972 Поблагодарили 3,104 раз за 848 сообщений Репа: 1862	Успешно снял FRP на Fly FS406 (SC7731C) Operation : Format File System / Reset Settings [ v1.24 ] ==== Wait for phone... Phone found! [ 164 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Checking Structure ... Detected eMMC Flash , Structure detect Ok! eMMC phone detected! Will use 'Safe Format' mode! Mount : /data Size : 0x0000000070CF7000 State : 0x0001 Mount : /cache Size : 0x0000000009600000 State : 0x0001 Prepare Ok! Format Ok! Don't touch phone, until it fully bootup to "Welcome Screen"! Android 5.x : Reset FRP Lock Reset Ok! Done! Elapsed: 00:00:28 Reconnect Power/Cable! PS Долго не мог подключить этот хитрый Fly к компу. Оказалось, чтобы подключить его, нужно сначала вставить USB кабель, а потом зажать клавишу "Громкость -". JayDi респект __________________ *Что бы ты ни сделал в жизни — это будет незначительно. Но очень важно, чтобы ты это сделал*

10.02.2017, 22:20	#17
cloud Новичок Регистрация: 21.12.2005 Сообщений: 12 Поблагодарил: 1 Поблагодарили 2 раз в одном сообщении Репа: 0	Fly Stratus 6 FS407 Check/Read Info [ v1.24 ] 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 15 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FLASH : eMMC Flash , Structure : Ok! Reading extended info ... Model Name : FS407 Model Brand : Fly Model Device: Stratus_6 AndrVersion : 6.0 BaseBand CPU: SP7731CEB CompileDate : 27.10.2016 10:49:41 Project Ver : SW10_FLY_FS407_2016_10_27 Model Ext : FS407 ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!! Elapsed: 00:00:15 Reconnect Power/Cable! Read NV [ v1.24 ] 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 15 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! Detected eMMC Flash , Structure detect Ok! Read GSM NV Read WCN NV Read Ok , 0x00032950 Saved to : C:\Firmware\Fly_Stratus_6_FS407_SPD_Infinity\SW10_ 2016_10_27\CX_SPDNV.spdnv Elapsed: 00:00:37 Reconnect Power/Cable! Read FullFlash [ v1.24 ] 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 15 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Detected eMMC Flash , Structure detect Ok! [FW_READER] : Prepare Ok! - > Wait phone connected ... Phone found! [ 15 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! - > Wait phone connected ... Phone found! [ 15 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! Model Name : FS407 Model Brand : Fly Model Device: Stratus_6 AndrVersion : 6.0 BaseBand CPU: SP7731CEB Project Ver : SW10_FLY_FS407_2016_10_27 Model Ext : FS407 [Read Mode] : HSUSB : 0x3000 [FW_READER] : Reading Firmware Now ... [Read Ok] : u-boot-spl-16k.bin [Read Ok] : u-boot.bin [Read Ok] : prodnv.img [Read Ok] : sc7731C_CP0_modem.bin [Read Ok] : DSP_DM_Gx.bin [Read Ok] : nvitem_w.bin [Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin [Read Ok] : nvitem_wcn.bin [Read Ok] : logo_480x854.bin [Read Ok] : fblogo_480x854.bin [Read Ok] : boot.img [Read Ok] : system.img [Read Ok] : sysinfo.img [Build Ok] : cache.img [Read Ok] : recovery.img [Read Ok] : udc_config.bin [Build Ok] : userdata.img AndroidInfo created Firmware Size : 1787 MiB Saved to : C:\Firmware\Fly_Stratus_6_FS407_SPD_Infinity\SW10_ 2016_10_27\SP7731CEB_Stratus_6_6.0_SW10_FLY_FS407_ 2016_10_27_FS407\ Done! Elapsed: 00:05:44 Reconnect Power/Cable!

21.01.2017, 17:26	#11
JayDi Регистрация: 24.02.2007 Адрес: Россия, Москва Сообщений: 792 Поблагодарил: 177 Поблагодарили 1,852 раз за 461 сообщений Репа: 1059	Не читается граф ключ на 6 и выше, там "GateKeeper" стоит.

01.02.2017, 23:48	#14
JayDi Регистрация: 24.02.2007 Адрес: Россия, Москва Сообщений: 792 Поблагодарил: 177 Поблагодарили 1,852 раз за 461 сообщений Репа: 1059	Можно иначе - кабель, кнопки, батарейку после.

17.02.2017, 09:48	#18
SurTaX Пользователь Регистрация: 02.02.2012 Сообщений: 57 Поблагодарил: 0 Поблагодарили 58 раз за 17 сообщений Репа: 70	Lenovo A396 SC8830 NAND Reset User Code лог Operation : Format File System / Reset Settings [ v1.24 ] Settings : SmartFormat is On 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 17 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC8830 Loader NAND v1.1 Infinity Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Checking Structure ... Detected NAND Flash , Structure detect Ok! Formatting NAND Flash Format UserData Format Ok! Format Cache Format Ok! Done! Elapsed: 00:00:39 Reconnect Power/Cable! Последний раз редактировалось vekt; 17.02.2017 в 10:29.

Похожие темы
Тема	Автор	Раздел	Ответов	Последнее сообщение
Обновление ПО для NCK Dongle / NCK Box	serpas007	NCK Dongle / NCK Box Team	184	18.02.2023 23:16
Успешное применение, без комментариев [CM2MTK MediaTek]	yurii-62	Infinity Box	316	26.08.2022 00:51
Успешное применение Medusa	fedja	Medusa JTAG Box	0	06.12.2016 23:22
Применение Infinity PinFinder без карты infinity	Romych78	Infinity Box	5	04.02.2009 12:14