SM-T705 замена eMMC требуется помощь

[alexece]

Имеется планшет. Нужно заменить память. Стояла THGBMBG7D2KBAIL

Z3X EasyJtag Software ver. 2.1.0.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: ********************, ,FW Ver.: 01.54
CMD Pullup Level:2134 mV
CMD Active Level:3269 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 11010030313647453204E3E849FD7120

EMMC CSD : D05E00320F5903FFFFFFFFEF924000D2

EMMC Manufacturer ID: 0011 , OEM ID: 0100
EMMC Date: 07/2014  Rev.0x4
EMMC NAME: <b>016GE2</b> , S/N: 3823651325
EMMC NAME (HEX): 30313647453200 
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
  Extended CSD rev 1.7 (MMC 5.0)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits  , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

 Device support partitioning feature

 Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

Backup saved: 016GE2_3823651325_20160514_1422.extcsd
Done.

Поставил KMVTU000LM-B503 (читал, что заменяемые)

Z3X EasyJtag Software ver. 2.1.0.0
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: ********************, ,FW Ver.: 01.54
CMD Pullup Level:453 mV
CMD Active Level:2217 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 15010056545530304DFC3D39868641FA

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014  Rev.0xFC
EMMC NAME: <b>VTU00M</b> , S/N: 1027180166
EMMC NAME (HEX): 56545530304D00 
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits  , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

 Device support partitioning feature

 Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

Backup saved: VTU00M_1027180166_20160515_1615.extcsd
Done.

Слил с родной флешки ROM1 2Gb и 1Gb, ROM2 4Mb прописываю в новую флеш все одно не входит в режим прошивки. Что ему надо прописать?