S5250 Repair Boot не выходит

[slen79]

День добрый! Пришло тело в уваленым бутом. Я смастерил кабель с 530Ком, и подцепил к UFS. Теперь ситуация такая при нажатии Boot Repair:

Connect Phone to RJ-45 Without Battery !
Power BAT+ from RJ45 V-BAT !
File: \S5250XEJI9\BOOTFILES\bcmboot.img
S5250-img, START: 00000000 SIZE: 00020130
NAND Write Complete
File: \S5250XEJI9\BOOTFILES\boot2.img
S5250-img, START: 00040000 SIZE: 0008E258
NAND Write Failed

Скоростями игрался, в разные моменты питание подавал и отключал.
Что еще можно предпринять?

[slen79]

Флеш Samsung, вот что пишет RIFF по этому поводу:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [Samsung S5250]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 3.06V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB

Flashing the dead body...OK
WARNING: Bad Block Error (0x25) at 0x00040000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x000C0000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x00140000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x001C0000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x00240000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x002C0000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x1DD40000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x1FF40000 is handled as Cut Excess.
Resurrection complete!

Я так понимаю что теперь можно было бы его пробовать шить, но на ЮСБ тел никак не реагирует.... в донлоад не входит. Что делать?

[jblack]

Флеш Samsung, вот что пишет RIFF по этому поводу:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.24, JTAG Manager Version: 1.32
Selected Resurrector: [Samsung S5250]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 3.06V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB

Flashing the dead body...OK
WARNING: Bad Block Error (0x25) at 0x00040000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x000C0000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x00140000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x001C0000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x00240000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x002C0000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x1DD40000 is handled as Cut Excess.
WARNING: Bad Block Error (0x25) at 0x1FF40000 is handled as Cut Excess.
Resurrection complete!

Я так понимаю что теперь можно было бы его пробовать шить, но на ЮСБ тел никак не реагирует.... в донлоад не входит. Что делать?

Чего тут шить, тебе пишет: Внимание ошибка плохой блок по адресу такому то.

Тут только катать или менять.