acidzone
14.09.2011, 23:21
при попытке сделать read detailed information инфинити пишет следующее:
COM1 [VCP1] selected
module v4.00
Device: _Autodetect MT6228-6268 NAND
Checking data, wait...
Action: read firmware NAND
interface: BROM_DLL_v3.1044.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8A04:8A01
status: FF
bbchip bl ver: FE
NOR flash id[0000]: 0000:000000000000 [AMD] AM29DL323D
chip size: 0Mb
otp status/size: S_DONE/00000000
NAND flash id[0000]: 0000:000000000000 [SAMSUNG] K9F5608Q0C
chip size: 0Mb
page/spare size: 0000/0000
pages per block: 0000
bits i/o: 00
address cycles: 00
internal RAM size: 00000000
external RAM [HW_RAM_UNKNOWN, CS0] size: 00000000
error: can not boot device: 0FA4:S_FT_DA_INIT_SYNC_ERROR
error: last error: 0FA4:S_FT_DA_INIT_SYNC_ERROR
Disconnect...
done
Finished, time used: 21 sec
Remove/Install battery now !
COM1 [VCP1] selected
module v4.00
Device: _Autodetect MT6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: read/check information
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6235:8A04:8A01]...
CPU: MT6235
high speed boot Off
chip: 0000:0000:0003
status: FF
high speed boot Off
boot packet size: 0400
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 19 sec
Remove/Install battery now !
Кушает при нажатии 20 мА. Микрухи пропаял, поведение не изменилось. В чем может быть проблема??? подозреваю флеху, но терзают меня смутные сомнения...
COM1 [VCP1] selected
module v4.00
Device: _Autodetect MT6228-6268 NAND
Checking data, wait...
Action: read firmware NAND
interface: BROM_DLL_v3.1044.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8A04:8A01
status: FF
bbchip bl ver: FE
NOR flash id[0000]: 0000:000000000000 [AMD] AM29DL323D
chip size: 0Mb
otp status/size: S_DONE/00000000
NAND flash id[0000]: 0000:000000000000 [SAMSUNG] K9F5608Q0C
chip size: 0Mb
page/spare size: 0000/0000
pages per block: 0000
bits i/o: 00
address cycles: 00
internal RAM size: 00000000
external RAM [HW_RAM_UNKNOWN, CS0] size: 00000000
error: can not boot device: 0FA4:S_FT_DA_INIT_SYNC_ERROR
error: last error: 0FA4:S_FT_DA_INIT_SYNC_ERROR
Disconnect...
done
Finished, time used: 21 sec
Remove/Install battery now !
COM1 [VCP1] selected
module v4.00
Device: _Autodetect MT6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: read/check information
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6235:8A04:8A01]...
CPU: MT6235
high speed boot Off
chip: 0000:0000:0003
status: FF
high speed boot Off
boot packet size: 0400
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 19 sec
Remove/Install battery now !
Кушает при нажатии 20 мА. Микрухи пропаял, поведение не изменилось. В чем может быть проблема??? подозреваю флеху, но терзают меня смутные сомнения...