|
Ошибка при прошивке китайских телефонов "error: wrong answer: 00"
Не могу не прошить ни считать фулл с любого китайского телефона, пользуюсь инфинити в паре с ксинтелом (кстинтел служит исключительно для эмуляции ком-порта для связи с телефоном). До этого этот тандем работал нормально на другом компе, установил все на новый комп - не хочет считывать/записывать, при этом форматирует без проблем.
Пробовал переустанавливать дрова и на ксинтеле и на инфинити, также обновил инфинити, скачал последние апдейты chinise mobile 2.58, те же грабли.
Пользуюсь в паре т.к. не имею Пир-ридера, а отдельно каждый кабель паять тоже не то.
Вот один из Логов:
COM9 [Serial2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: read NOR flash
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:859C:FDBF
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd PL127J D 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd PL127J D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd PL127J D 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:29EA0000000000
flash: Amd PL127J D 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
warning: wrong cs at 0x00234E84, retry...
error: too many retries during read operation
error: wrong answer: CB
error: can't read security area#1
detect device identification#2...
detection phase #1...
error: wrong answer: 00
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
error: wrong answer: 00 : wrong answer after chip id request
error: wrong answer: FF : wrong answer after chip cfi request
error: wrong answer: 00 : wrong answer after chip id request
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
operation terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content...
error: wrong answer: 0B
Check firmware content Fail
Finished, time used: 78 sec
Remove/Install battery now !
|