A850 слетают имеи после прошивки, где подвог?

[Mr.Sunn]

Сильно не пинайте,тема думаю объезженная но стою в тупике, уже спотыкнулся с 3-мя аппаратами именно этой модели, тел пришел с ошибками процессов имеи в порядке


Итак порядок действий:

Read Info

tart at : [07.06.2017 / 12:41:35]
Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048600A30E493113
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048600A30E493113
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xF3032F923FCC98405C473B81A0FFDCB2
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : Lenovo
ProdName : aupres_row
ProdModel : Lenovo A850
Device : A850_ROW
AndroidVer: 4.2.2
MTKxCPU : MT6582
MTKxPRJ : ALPS.JB5.MP.V1

SECURITY :
IMEI_SW [1] : 864692022195308
IMEI_SW [2] : 864692022195316
BTMAC Addr : CC07E499598A
WiFi MAC : CC07E4A4598A

MODEM :
BaseBand : MT6582_S00_A850_ROW_V20_1_wg_n

как видим, имена маки присутствуют, делаю бекам NWRAM (на всяк случай)

Read NVRAM

Start at : [07.06.2017 / 12:42:00]
Operation : Read NVRAM [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048600A30E493113
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048600A30E493113
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xF3032F923FCC98405C473B81A0FFDCB2
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[Info] : BaseBand : MT6582_S00_A850_ROW_V20_1_wg_n

NVM Read Ok, MT6582_S00_A850_ROW_V20_1_wg_n_eMMC.spnv

Done!
Elapsed: 00:00:49
Reconnect Power/Cable!

Finish at : [07.06.2017 / 12:42:50]

Прошиваем

Scatter Load Ok , BaseBand : MT6582 , Project : aupres_row , Storage : EMMC
Files found : 13 , Set to Flash : 12
Ready to Flash!

Start at : [07.06.2017 / 12:43:19]
Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048600A30E493113
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048600A30E493113
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xF3032F923FCC98405C473B81A0FFDCB2
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : aupres_row , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Disabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3764 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001400000-0x0000000000100000
Erase : 0x0000000003100000-0x00000000B9A80000
Flash Pre-Erase Done, time used : 00:00:02

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_aupres_row.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0014
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : EBR2
Image Flash Ok
Flash now : PRELOAD
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:04:59


Update Mirror PMT
Update Done!

Update RomInfo done

тело не включилось ну не впервой, прошиваю флеш тулом в режиме донлоад ошибка, в режиме финваер обгрейд порошилось, включилось, имена, естественно, инвалид!! Ну у нас же есть бекап НВ! восстанавливаем

Write NVRAM

. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048600A30E493113
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048600A30E493113
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xF3032F923FCC98405C473B81A0FFDCB2
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[NVCheck] : BBID : MT6582 , NVID : MT6582
[NVM] : Write Ok!

[Info] : NVRAM Repair on erased/damaged phone :
1. Fix Unknown BaseBand
2. Power On phone, check BB state
3. Write NVRAM
4. Repair Security

Done!
Elapsed: 00:00:36
Reconnect Power/Cable!

Finish at : [07.06.2017 / 13:13:20]

Start at : [07.06.2017 / 13:13:32]
Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Open port error , something went wrong!
Boot Error!

Operation Failed
Elapsed: 00:00:04
Reconnect Power/Cable!

Finish at : [07.06.2017 / 13:13:36]

Start at : [07.06.2017 / 13:13:48]
Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048600A30E493113
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048600A30E493113
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0xF3032F923FCC98405C473B81A0FFDCB2
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : Lenovo
ProdName : aupres_row
ProdModel : Lenovo A850
Device : A850_ROW
AndroidVer: 4.2.2
MTKxCPU : MT6582
MTKxPRJ : ALPS.JB5.MP.V1

SECURITY :
IMEI_SW [1] : 864692022195308
IMEI_SW [2] : 864692022195316
BTMAC Addr : CC07e4E499598A
WiFi MAC : CC07E4A4598A

MODEM :
BaseBand : MT6582_S00_A850_ROW_V20_1_wg_n

Done!
Elapsed: 00:00:07
Reconnect Power/Cable!

Видим в логе имена присутствуют а на самом деле звонки не делает и
на экране видим все тот же инвалид, ну думается поправим

Repair Security

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 42 ]
Sync...
Init Ok, waiting for phone ...
Reading initial info, wait...
Phone Info :
Security Info :
IMEI [1] : Damaged!
IMEI [2] : Damaged or not exists
Read Ok!
Update IMEI[1] to : 864692022195308 failed , record not exist or NVRAM damaged!
Update IMEI[2] to : 864692022195316 failed , record not exist or NVRAM damaged!

Done!
Elapsed: 00:05:36
Reconnect Power/Cable!

Finish at : [07.06.2017 / 13:28:52]

обидно, вобщем, за 4 месяца эксплуатации Инфинити кнопочка Repair Security у меня ни разу не заработала (((

в итоге, делаю формат через флештул, прописую через флеш тул, имей и мак адреса правим MauI MATA. Где я делаю ошибку? банальная прошивка вливается в часовую метушню

[slavkinj]

А сброс после прошивки делали ?

И еще :

[Info] : NVRAM Repair on erased/damaged phone :
1. Fix Unknown BaseBand

[jblack]

Сообщение от Mr.Sunn

тело не включилось ну не впервой, прошиваю флеш тулом в режиме донлоад ошибка, в режиме финваер обгрейд порошилось, включилось, имена, естественно, инвалид!! Ну у нас же есть бекап НВ! восстанавливаем

обидно, вобщем, за 4 месяца эксплуатации Инфинити кнопочка Repair Security у меня ни разу не заработала (((

в итоге, делаю формат через флештул, прописую через флеш тул, имей и мак адреса правим MauI MATA. Где я делаю ошибку? банальная прошивка вливается в часовую метушню

А для кого инструкция в логе:

[Info] : NVRAM Repair on erased/damaged phone :
1. Fix Unknown BaseBand
2. Power On phone, check BB state
3. Write NVRAM
4. Repair Security

Перед записью NV сначала жамкаем Fix Unknown BaseBand и обязательно включаем телефон, потом только пишем NV далее если NV был чужим, правим цифорки.

[Mr.Sunn]

Сообщение от jblack

А для кого инструкция в логе:



Перед записью NV сначала жамкаем Fix Unknown BaseBand и обязательно включаем телефон, потом только пишем NV далее если NV был чужим, правим цифорки.

вот этого какраз и не видел в логах