Nokia 5228. После erase.

[marg]

Телефон принесли с проблемой "память заполнена" при входе в проигрыватель. Прошивка разными версиями, формат результата не дал. Сделал все бэкапы сертификатов, пм а, рпл циклоном. После, полный эрейз. Теперь не могу записать бэкапы и прошить. Может кто сталкивался, дайте совет ?

Вот собственно лог записи серт-ов

Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101051105
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		1310001388A300525DD5F76EEC070C3FFA5E4D60
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	B8C3ADECFC997FCD8081D3DEAF870B8C
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.40.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0xFFFFFFFF00000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC004000000231, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.11.40.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
Warning: PAPUBKEYS Hash Missing!
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Processing 1310001388A300525DD5F76EEC070C3FFA5E4D60.C00037C8...
Failed to Write C000  Certificate -> Unknown SubSystem name (C000) detected