Кит N81 не вкл после прошивки инфинити

[smit7777]

доброго времени суток. Такая проблемка, инфинити слил с кита N81 епром и фул ради эксперимента. Потом залил обратно. Тело перестало включаться. До этого китов не шил, подскажите што я делаю ни так, вот лог операций:

COM9 selected
Device: Autodetect 6205-6227,6228 NOR
Checking data, wait...
advanced flash detection active
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization
skip: Language Pack
write: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
921600
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
Can't detect eeprom area
Do you want to use standard eeprom address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard eeprom address selected by user
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area: 00000000:00E00000-00FFFFFF
reading [eeprom]...
file saved: backup_eeprom_20080111-154206.B0E.bin
flash: EC257E25082501:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data damaged
identification detection finished
Area: Firmware
flash: EC257E25082501:29EA0000000000
Write: Firmware
Area: Eeprom
flash: EC257E25082501:29EA0000000000
Write: Eeprom
structure: 2nd [enhanced] (or higher) generation
identification data damaged
identification detection finished
device-id: 8E8945E1
protocol ver: 04
ver. sw1: BR26_05C_PCB01_GPRS_MT6226_S01.BR26_23_09.BIN
ver. sw2: BR26_23.09
ffs offset/size: 00E00000/00200000
warning: invalid identification, ask/rpl calculation reqired
error: rpl file not found: D:\Program Files\InfinityBox\ChineseMiracle\id.8E8945E1._BR26 _05C_PCB01_GPRS_MT6226_S01.BR26_23_09.BIN_81BDE418 _.rpl
file saved: id.8E8945E1.[BR26_05C_PCB01_GPRS_MT6226_S01.BR26_23_09.BIN_81BD E418].ask
ASK file created Ok
Probably identification data damaged,
device id: 8E8945E1
firmware version:
BR26_05C_PCB01_GPRS_MT6226_S01.BR26_23_09.BIN_81BD E418
RPL file must be in folder: D:\Program Files\InfinityBox\ChineseMiracle\
You can create RPL from ASK via client/server right now and press YES.

Do you want to write RPL file now ?
error: rpl file not found: D:\Program Files\InfinityBox\ChineseMiracle\id.8E8945E1._BR26 _05C_PCB01_GPRS_MT6226_S01.BR26_23_09.BIN_81BDE418 _.rpl
Write Done
Finished, time used: 676 sec
Remove/Install battery now !