Обновления RIFFbox JTAG

[yurii-62]

03.04.2012
RIFF JTAG – Samsung Galaxy Mini – GT-S5570i Unbrick – Boot repair supported
Repairing bricked Samsung S5570i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.
To resurrect Samsung S5570i:
Solder JTAG cable to Samsung S5570i JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung S5570i is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.
.

источник:
http://www.jtagbox.com/jtag-news/rif...pair-supported

[yurii-62]

06.04.2012

RIFF JTAG - MIPS32 Поддержка RIFF Box прошивка v1.32, RIFF JTAG Manager v1.42 выпущен

RIFF Box Firmware 1,32
Добавлена поддержка архитектуры MIPS32 для TAP контроллера с ИК длина = 05 бит (например ALI 3329 процессоров)
Добавлена поддержка архитектуры MIPS32 для TAP контроллера с ИК длина = 08 бит (например, процессор BCM5352)
Некоторые незначительные улучшения в TEGRA2
RIFF JTAG Manager 1,42
Добавлена поддержка архитектуры MIPS32!
Добавлено сочетание клавиш "Ctrl + F" для быстрого и удобного отображения "Поиск DLL" окна.
Это работает с любой страницы Менеджер JTAG, это более удобная альтернатива обычному действию поиска, когда пользователь должен перейти на воскресение страницы и нажмите кнопку "Поиск DLL" кнопку.
Добавлен "riffpbin" формат поддержки DCC Read / Write страница операций
Некоторые незначительные косметические исправления
Новый запуск логотипа!


Статья:
http://www.jtagbox.com/jtag-news/rif...-v142-released

[DB2020_Logs]

06.04.2012 RIFF JTAG – HTC Flyer (PG41100) Unbrick, Unlock, IMEI, S-off, update supported

Repairing bricked HTC Flyer (PG41100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so writing to DBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into DBL zone and will respond with success code as if flashing succeeded. In this way DBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.11.0003 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4110000’.
There is option to reflash android BOOT and RECOVERY zones. Recovery zone is flashed with ClockworkMod Recovery 4.0.1.4. In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by clicking “Make S-OFF” checkbox in the resurrector settings.
Sometimes (for example after rooting attempts) phone has a modified DBL loader (which may not accept official HTC boot files). To restore phone functionality you need to reflash DBL loader. There is option to reflash DBL code (DBL area will be temporary unlocked for reflashing). But please note, reflashing DBL area is very dangerous, since in case flashing stops in the middle, you will have briked phone with permanently disabled JTAG interface.
Please note, if your phone has the DBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Flyer:

• Solder JTAG cable to HTC Flyer JTAG pads;
• Insert battery and connect USB Data cable;
• Make sure HTC Flyer is selected in the list of models;
• If you use only battery, press Power On key;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

[yurii-62]

11.04.2012

RIFF JTAG - HTC Flyer Wi-Fi (PG41400) Unbrick, S-офф, CID обновление поддерживается
Ремонт кирпичом HTC Flyer Wi-Fi (PG41400) легко с RIFF Box. Телефон является автоматическое питание с USB кабель подключен к компьютеру в то время как батарея подключена. Обратите внимание, что батарея presense не требуется.
Некоторые из них (или все) изменения досок HTC Flyer есть JTAG интерфейс отключен (что это разрешить MARM JTAG Предохранитель перегорел в MSM8255 чип). В этом случае JTAG может быть включена только сама прошивка. Это делается путем DBL погрузчик, таким образом, запись в область DBL искусственно отключена в коде Loader ДКК. DCC Loader уберет все попытки в DBL зоне и будет реагировать с успехом код, как будто прошивка удалась. Таким образом, DBL зона защищена в то время как пользователь все еще может записать полный графических файлов без проблем.
Для восстановления надо будет перепрошит зону загрузки радио (за исключением области DBL) и переписать SPL КПК на 1.11.0011 версии. В дополнение к SPL и радио зоны, зоны, которая содержит модель ID повторно прошить тоже. Таким образом, после восстановления телефон будет иметь модель ID = 'PG4140000.
Существует возможность перепрошить андроид загрузки и восстановления зоны. Восстановление зоны прошики с ClockworkMod восстановления 4.0.1.4. Кроме того, вы можете установить S-OFF (разблокировка HBOOT так что вы сможете прошить любой ROM), выбрав S-OFF HBOOT версии воскреситель настройки.
Иногда (например, после укоренения попыток) телефон имеет изменение DBL загрузчик (который не может принять официальный загрузочные файлы HTC). Для восстановления функций телефона необходимо перепрошить DBL погрузчика. Существует возможность перепрошить DBL код (DBL области будет временно разблокирована для перепрошивки). Но учтите, перепрошивки DBL области очень опасно, так как в случае мигание прекращается в середине, вы будете иметь briked телефон с инвалидами интерфейс JTAG.
Пожалуйста, обратите внимание, если ваш телефон имеет DBL загрузчик поврежден и MCU имеет JTAG предохранитель, то нет никакого способа, чтобы воскресить вашего телефона через интерфейс JTAG.
Чтобы восстановить HTC Flyer Wi-Fi:
Припой JTAG кабель для HTC Flyer JTAG площадок;
Вставьте аккумулятор и подключите USB кабель передачи данных;
Убедитесь, что HTC Flyer (PG41400) выбрана в списке моделей;
Если вы используете только аккумулятор, нажмите питания ключа;
Нажмите кнопку Воскрешение;
Подождите, пока программное обеспечение сигнализирует об успешном завершении операции;
Отключите питание, де-JTAG пайки проводов;

Теперь телефон находится в загрузочном состоянии, то есть, даже если она не начнет работать нормально можно прошивать его с помощью известных методов прошивки. Вы можете использовать CWM восстановления прошить любой ZIP файл - для этого во время загрузки добавьте воскресение и ВОССТАНОВЛЕНИЕ зон воскреснуть тоже.
Чтобы войти в режим загрузки:
Отключите кабель ПК;
Вставьте батареи;
Hold 'Volume Down "ключ и" Power ON "нажмите на кнопку.
иточник: http://www.jtagbox.com/jtag-news/rif...date-supported

[Pеrеsvеt]

....................

[yurii-62]

24.04.2012 RIFF JTAG – HTC via USB Cable Support added
Whats new:
Released support for HTC phones based on MSM8x55 CPU, which are enumerated on USB port as “QHUSB_DLOAD” device. Now it’s possible to repair these phones without soldering any wires. Even without opening !
Following models are supported at the moment:
HTC Desire HD (HTC Ace)
HTC Desire S (HTC Saga)
HTC Desire Z (HTC Vision)
HTC Flyer 3G
HTC Flyer WiFi
HTC Evo View 4G
It is possible to force QHUSB_DLOAD mode by disabling Vdd line on eMMC chip. Check Desire S TP info for example. This means, You can work with any MSM8255/MSM8655 based HTC phone, as long as You force it into QHUSB_DLOAD mode.
Follow this procedure if You want to use these updates:
Connect Your phone to USB port and install QHUSB_DLOAD device driver (C:\Program Files (x86)\RIFF Box JTAG Manager\Drivers\32Bit\QDLOADER)
Launch JTAG Manager, select appropriate Model DLL and click desired button
Install “RIFF Box DCCLoader USB Interface” port driver (C:\Users\Admin\Desktop\Drivers_64Bit_WorkedForMe\ Drivers\64Bit\DCCLDR)
If required, repeat the procedure (sometimes required if device is connected for first time)
We will release USB support for rest of the models on these CPU-s in following days.
To download and install new updates – simply click “Check for Updates” button on Box Service TAB.
Share!



Источник:
http://www.jtagbox.com/jtag-news/rif...-support-added

[DB2020_Logs]

27.04.2012 RIFF JTAG – HTC via USB more phones supported

• HTC Thunderbolt USB support added
• HTC Sensation XL USB support added
• HTC Inspire USB support added
• HTC Incredible S USB support added
• HTC Incredible 2 USB support added

These new updates will allow You to use USB cable to perform any operation on listed models. Remember that this work if Your phone is enumerated on USB port as QHUSB_Dload or Qualcomm HS-USB QDLoader device.
In case phone is not enumerated, You might need to use test point method first.
Please visit RIFF FAQ section to see how to install drivers, and how to find eMMC Vdd test points:

How to install QHUSB_DLOAD driver
How to install “RIFF BOX DCCLoader USB Interface Port” Windows 7 64bit driver

If You need to repair phone after replacing eMMC chip, these are the steps:

• Launch eMMC MBR/EBR partitioning tool
• Open desired partitioning file
• Click “Load Image from file”
• Click “Repartition eMMC”
• Close the eMMC plugin
• Click “Resurrection” and select all options to be repaired, including IMEI and CID
• Click “Resurrect”

[DB2020_Logs]

RIFF JTAG-RIFF JTAG Manager v1.43

Скачать >>>

This will install following files to Your computer:

• JTAG Manager software v1.43
• RIFF Box Firmware v1.32
• RIFF Box control port driver
• RIFF Box update port driver
• RIFF DCC USBLoader driver
• QUALCOMM QHUSB_DLOAD driver

After You execute setup, it will install all files to desired destination, and launch drivers installer script.
Take note, If You’re using Windows XP, You’ll have to provide drivers location to Hardware Installation Wizard after connecting devices for first time.

[yurii-62]

На русском

Авторы RIFF JTAG анонсировали новые версии приложения JTAG Manager software 1.43, микропрограммы бокса RIFF Box Firmware 1.32 и необходимых в работе драйверов.


Обновлено в ПО RIFF JTAG Box:

Данное обновление инсталлирует следующие файлы и приложения на Ваш ПК:
JTAG Manager software версии 1.43
RIFF Box Firmware версии 1.32
Драйвер контрольного порта RIFF Box
Драйвер порта обновления RIFF Box
Драйвер RIFF DCC USBLoader
Драйвер QUALCOMM QHUSB_DLOAD

Во время установки указанные приложения и файлы записываются в указанную папку и запускается скрипт установки драйверов. Помните, что если Вы используете ОС Windows XP, Вам потребуется указать местоположение файлов драйверов при первом подключении устройств.

[yurii-62]

04.05.2012

RIFF JTAG – Samsung SGH-T679 Exhibit II 4G (Samsung Ancora) Unbrick – Dead Boot repair supported
Repairing bricked Samsung T679 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is multi-core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.
To resurrect Samsung T679:
Solder JTAG cable to Samsung T679 JTAG pads;
Make sure Samsung T679 is selected in the list of models;
Insert battery and connect USB Data cable;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.
.
источник:
http://www.jtagbox.com/jtag-news/rif...pair-supported

[DB2020_Logs]

Драйвера для RIFF Box и HTC USB с автоматической установкой.
Вам больше не потребуется указывать расположение драйверов при подключении бокса к другому порту.

При возникновении проблем с установкой драйверов обращайтесь в ЛС к Pasha.T

Прямая ссылка - http://www.jtagbox.com/downloads/RiF...rs_Pasha.T.exe

[vekt]

Сообщение от DB2020_Logs

Драйвера для RIFF Box и HTC USB с автоматической установкой.
Вам больше не потребуется указывать расположение драйверов при подключении бокса к другому порту.

При возникновении проблем с установкой драйверов обращайтесь в ЛС к Pasha.T

Прямая ссылка - http://www.jtagbox.com/downloads/RiF...rs_Pasha.T.exe

Он сам то их проверял? Установил, система при подключении бокса видит его, но сюита при запуске ругается на невозможность открыть порт на котором висит бокс... В топку такие дрова, лучше ручками самому ставить!

[paganini]

RIFF JTAG добавил в последнем обновлении своего ПО поддержку восстановления модели Samsung SPH-D710 Galaxy S2 (Epic Touch 4G, Samsung Within)

Подробнее: http://www.jtagbox.com/jtag-news/rif...air-supported/
Источник: http://forum.gsmhosting.com/vbb/8400409-post249.html

http://www.jtagbox.com/
http://www.riffbox.org/
Legija, Rocker team

[fedyaGSM]

RIFF JTAG - Weekend Updates
18.05.2012 RIFF JTAG – Weekend updates:

[/CENTER]


Whats new:
Samsung B7320 unbrick/boot repair support added
HTC Sensation 4G (PG581000) Unbrick, Unlock, S-Off, SuperCID support added
HTC Sensation (PG581300/PG583101) Unlock support added
HTC Evo 3D Unlock support added
Bug Fix updates:
HTC Desire HD Support for new board revisions with hboot 2.xx (No Network problem)
HTC Wildfire S Proximity sensor fix
RIFF Torrent tracker:
RiffBox Setup 18.05.2012 v1
Please click “Check for updates” button in RIFF JTAG Manager to download new files.

RIFF Box FAQ:
RIFF JTAG Box FAQ - RIFF JTAG Error codes and troubleshooting
RIFF JTAG Box FAQ - RIFF JTAG Box setup
RIFF JTAG Box FAQ - JTAG Manager - DCC Read/Write TAB
RIFF JTAG Box FAQ - How to use QUALCOMM eMMC MBR/EBR Partitioning plugin


www.jtagbox.com

[zarifjan]

RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Surround (PD26100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.74.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD26*********’.

.To resurrect HTC Surround (PD26100):
.Solder JTAG cable to HTC Surround JTAG pads;
.Insert USB Data cable into board and PC;
.Make sure HTC Surround (PD26100) is selected in the list of models;
.If you use battery, press Power On key;
.Click Resurrect button;
.Wait till software signals a successful operation completion;
. Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:
.Disconnect PC cable;
.Insert battery;
.Hold ‘Volume Down’ key and press ‘Power ON’ button.


www.jtagbox.com

[Jagger]

по русски...

RIFF JTAG добавил в последнем обновлении библиотек своего ПО поддержку восстановления загрузчика, SuperCID и IMEI, а так же разблокировку модели HTC 7 Surround T8788 (HTC Mondrian).



Добавлено в этом выпуске ПО RIFF JTAG:

Поддержка восстановления модели:

- HTC 7 Surround T8788 (HTC Mondrian)

Доступны операции:

- восстановление загрузчика,
- разблокировка,
- восстановление SuperCID,
- восстановление IMEI.

Подробнее: forum.gsmhosting.com

http://www.jtagbox.com/
http://www.riffbox.org/
Legija, Rocker team

[DB2020_Logs]

31.05.2012 RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Repairing bricked HTC OneV (PK76100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.16.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7610000’.
There is option to reflash android BOOT and RECOVERY zones.
To resurrect HTC OneV via USB Cable:
If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;

• Make sure HTC OneVC (PK76100) is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press ‘Power ON’ button.

[DB2020_Logs]

12.06.2012 RIFF JTAG – HTC Rhyme (HTC Bliss) Unbrick, Unlock, SuperCID and IMEI Update via USB Supported

Repairing bricked HTC Rhyme (PI46100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).

In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.30.0004 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI4610000’.
There is option to reflash android BOOT and RECOVERY zones.

To resurrect HTC Rhyme via USB Cable:
If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;

Make sure HTC Rhyme (PI46100) is selected in the list of models;

• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Depower the phone;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press ‘Power ON’ button.

------------------------------------------------------------------------------------------------------------------------

12.06.2012 RIFF JTAG – HTC Radar (HTC Omega) Unbrick, Unlock, SuperCID and IMEI update via USB cable supported

Repairing bricked HTC Radar (PI06100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).

In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI0610000’.

To resurrect HTC Radar via USB Cable:

If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;


Make sure HTC Radar (PI06100) is selected in the list of models;

• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Depower the phone;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

[ivan_ashurov]

Свежее обновление программатора RIFF JTAG дает пользователям эксклюзивную возможность проведения операций с моделями HTC Radar и HTC Rhyme через USB.

Новые возможности RIFF JTAG:
HTC Rhyme (HTC Bliss) - реанимация/разблокировка/восстановление IMEI через USB, впервые в мире.
HTC Radar (HTC Omega) - реанимация/разблокировка/восстановление IMEI через USB, впервые в мире.
Исправлено:

Поддержка HTC One V
Исправлена проблема разделов DBL
Добавлено на торрент-треккер RIFF:

http://tracker.riffbox.org/download.php?torrent=47
Источник:
forum.gsmhosting.com

http://www.jtagbox.com/
http://www.riffbox.org/

[gaz2402]

Whats new:
ZTE S170 support added
ZTE S180 support added
ZTE S165 support added
ZTE FWPC26 support added


Bug fixes:



HTC_Flyer_PG41100.dll
HTC_Flyer_PG41400.dll


PLL frequency is lowered, now no more RAM memory test failed bug error at the connection stage.

Читать здесь-http://forum.gsmhosting.com/vbb/f475...odels-1490990/